PDA

View Full Version : Keith's trial design



keithtty
02-14-2009, 06:48 AM
Pretty taken into the idea of an algae scrubber, so I made a low cost one.

Chopping board - $3.5 but ended up using my old one...
Light holder - $5
PVC piping - $3.2
Flood light - $30[attachment=0:1jz8xffk]DSC_0017.JPG[/attachment:1jz8xffk]

keithtty
02-14-2009, 06:50 AM
light bulb

keithtty
02-14-2009, 06:51 AM
PVC pipe with holes drilled into them.[attachment=0:wjuim7xp]DSC_0084.JPG[/attachment:wjuim7xp]

keithtty
02-14-2009, 06:52 AM
Here is how it looks[attachment=0:1o475qog]DSC_0087.JPG[/attachment:1o475qog]

keithtty
02-14-2009, 06:53 AM
another look of the flow[attachment=0:301bix1i]DSC_0097.JPG[/attachment:301bix1i]

keithtty
02-14-2009, 06:54 AM
The entire set-up

Hope it works.

Not sure if the bulb will get spoilt like that. I feel the bulb makes the cabinet more hot now, but that would be an expected result, I guess.[attachment=0:v9e7q777]DSC_0093.JPG[/attachment:v9e7q777]

keithtty
02-14-2009, 06:55 AM
Too lazy to do testing, but will leave this part of the overflow alone. If it works, this should go away, right?
But actually, I made 2 changes, I also restarted my auto top up that tops up kalk....anyway, bottomline is too lazy to do testing - anyway no coral in the tank anyways.[attachment=0:1rv0bf2t]DSC_0100.JPG[/attachment:1rv0bf2t]

kcress
02-14-2009, 12:56 PM
Looks pretty good. I bet it will work fine.

Is the end of your board actually in the water? Splashing?

keithtty
02-14-2009, 06:43 PM
yes, end of the board touches the water. :D

SantaMonica
02-14-2009, 07:12 PM
Keith what bulb are you using? It should not make anything hot. The placement is very good however. Is it on a timer?

Do this to improve final results: Lay a sheet of rug or plastic canvas on top of the cutting board.

keithtty
02-21-2009, 04:45 PM
Here is the bulb:

keithtty
02-21-2009, 04:46 PM
Pic after 1st week of use.

keithtty
02-21-2009, 04:48 PM
bulb is on a timer: 16hours on, 8 hours off

zoa
02-21-2009, 06:52 PM
Yours looks similar to mine. I used a piece of tile.

On the piece of plastic canvas, I have tried to put a piece on mine and the water doesn't flow across the screen. Just kinda under it. I would suspect that you would get the same results. I have twice the flow going over mine as I have upgraded my pump so I now flow 400GPH over a 7" wide screen.

Maybe SM can chime in here and tell how it should be. What I mean is, to let us know how the water should flow on this style of scrubber.
Will the water go over the screen when algae starts to grow?

SantaMonica
02-22-2009, 11:25 AM
The difference that the canvas makes is when algae is thick, and when you clean it. When it's thick, it will let go by itself if it can't grab onto the screen. So without a screen, it's performance is reduced as pieces let go into the tank. And when you clean without a screen, you have nothing left over, so you have to wait a few days before filtering gets going again.

It's ok if the water goes under, because after the growing get full, it will grow through the screen.

keithtty
02-23-2009, 01:51 AM
The cutting board I am using actually has a rough, corrugated surface (not to mention all the cut lines, becuase I ended up using the old one). I think algae will stick, but I will keep a close watch on that.

keithtty
03-01-2009, 01:10 AM
updates 2/28

SantaMonica
03-01-2009, 11:13 AM
I remember that cutting boards are made out of Teflon. So when green algae gets thick enough, the water flow will pull them off of the surface. You'll have to clean more often to offset this.

keithtty
03-01-2009, 02:21 PM
Going to be out of town this week, but I am going to add a platic canvas and increase the flow.

worley
03-02-2009, 02:40 AM
If it is teflon, that's PTFE (as in the plumber's tape and the type of plastic), apparently, it's considered to be the best low friction, no-slip surface available (used to coat windscreen wiper blades also so they don't stick to the glass), so probably not inherently good for algae to attach to as SantaMonica suggests =).
The other good thing about using a mesh on top is that the bits of algae get stuck in between the holes so when you clean it they can regrow nice and quickly, especially useful when doing one-sided lighting like this (exactly what I'll be doing).