SantaMonica HOG1.3

Subscribe to this topic HERE

HOG1.3(TM)

Purchase Here

HOG Scrubber®
Hang On Glass Upflow Algae Scrubber®
with Green Grabber(TM) surfaces

For 1/4" (6mm) to 5/8" (16mm) acrylic or glass walls. Eliminate water changes. Remove nuisance algae, nitrate and phosphate. Cultivate seaweed for feeding.

Attachment 5181 Attachment 5182 Attachment 5183 Attachment 5184 Attachment 5187 Attachment 5188 Attachment 5189 Attachment 5191 Attachment 5192 Attachment 5341 Attachment 5342 Attachment 5186 Attachment 5190 Attachment 5193 Attachment 5185

Purchase Here

From new to green in 3 cleanings:
http://youtu.be/utu2SADmj2g
Unboxing and Installation Videos:
https://www.youtube.com/watch?v=h_hjCZ8_2VE
http://youtu.be/IWX6UGmSyV0
First 7 Days Growth in Saltwater:
http://youtu.be/91jQAPB40OA
Comparison of HOG1.3 to the HOG2 and HOG3:
http://youtu.be/CQ6GLnL-Ecs

Get the no-overflow advantage of an upflow scrubber: since it is ALL underwater, it can't overflow onto your floor.

This is the first larger Hang-On-Glass version of the standard HOG.5, HOG1, and HOG1x algae scrubbers, which were the first HOG scrubbers available. This HOG1.3 offers much larger algae-attachment space to hold more growth between cleanings, and also stronger magnets to attach to thicker aquarium walls up to 5/8" (16mm) glass or acrylic. If your tank is larger than a nano, then you should consider this model or larger.

This HOG1.3 Scrubber has 30 square inches (187 square cm) of one-sided algal growth surface, which once growing is designed to absorb the nutrients from this much feeding per day:

1.3 Frozen cubes, or
13 Pinches of flake, or
13 Square inches (90 square cm) of nori, or
3.6 grams of pellets

The number of gallons or liters of water in your tank or sump does not matter. If you feed more than the above amounts you can get multiple HOG1.3 units; multiple units are preferred over one larger unit because you can clean one unit per week, and because you'll always have one unit filtering while the other one starts growing again after a cleaning. Multiple units are also good for backup. The magnets attach the outside cover to the inside cover through the aquarium wall, and can be used on glass or acrylic 1/4 inch (6 mm) to 5/8 inch (16 mm). Not more. If your aquarium wall is 3/4" (18mm) it might work but you won't know until you try; it would be better to put the HOG1.3 in your sump instead; it will work the same. Or you could rub a thin layer of silicone caulking into the LED OUTSIDE shell; after it dries overnight it will stay in place on thicker walls.

Purchase Here

Compared to the HOG2 and HOG3 which look the same in size, the HOG1.3 is meant for situations which don't have nutrient or algae problems. The large inside space of the growth compartment allows for lots of build up of algae over a long time, and the relatively low power 2 LED light grows algae at a nice comfortable pace. So this model is great for aquariums that are already in good shape, or new aquariums which don't have problems yet. It also probably will not require light-reduction to get started, like the stronger HOG2 or HOG3 might.

The Green-Grabber (tm) algal growth surface is so rough and prickly that it might be the roughest thing you've ever felt. A cactus might be sharper, but that's about it. Rough surfaces are critical for allowing algae to attach and grow and thus provide strong absorption of nutrients. The rock-hard protrusions stick straight out 1 to 3 mm. Old style algae scrubber screens are made from "slippery" plastic canvas that is used for sewing and knitting; algae takes a long time to attach to it. Green-Grabber (tm) growth surfaces are not plastic at all; instead they are rock hard and have jagged rough edges and points (don't let children play with them). And the white color of the Green-Grabber surface reflects as much light as possible, getting almost the effectiveness of a 2-sided growth surface even though it really only has a light on one side of the surface.

This is a hand-built Hang-On-Glass® (HOG) Upflow Algae Scrubber® (UAS) with a Green-Grabber (tm) growth surface, for glass or acrylic 1/4 inch (6 mm) to 5/8 inch (16 mm) thick. This is the typical thickness range for most aquariums, and larger sumps, however you should measure yours to be sure. If your tank uses thin 1/8" (3mm) glass such as many low-cost 10 gallon aquariums do, this filter is not recommended because the magnets are strong enough that they might crack the glass. You would be better off getting a lower cost HOG.5 filter.

No electrical parts go inside the aquarium; only air. And the air bubbler is already supplied (it's sealed behind the growth surface), so you don't have to get an airstone. The bubbler is simply vinyl air hose that has been cut lengthwise, and with cross-cuts, to form little flexible segments that are both adjustable and open-able to allow for easy cleaning. This HOG1.3 will run on both 120V and 240V, and comes with a 10 ft (300 cm) power cord with a U.S. plug. If you require a different plug you can get an adapter at any local hardware or travel store, or online, or you can cut off the U.S. plug and install your own plug from a hardware store.

Comes with 3 ft (90 cm) of vinyl airline, but requires an air pump that can pump at least 2.0 liters per minute (.07 cfm), preferrably more. A pump that says it can handle 2 or more airstones/outlets, or a pump with 2 tubing attachments instead of one, will be needed. You can have as much air as you like, however; 10 lpm pumps are no problem (although it will be louder). One powerful pump which works exceptionally well for a low cost is the Fusion 700 Air Pump from JW Pet. It is quiet and has two outputs which are adjustable by turning the control knob. Another even more powerful and completely silent pump, although more expensive and without a control, is the Whisper AP 300 from Tetra. With either pump you will need to combine the two outputs into one to feed the scrubber, using something such as the "Tee" air line tubing fitting from Tom Aquatics (which we include with the Fusion 700). Make sure to put the air pump above the aquarium so that it will not drain any water if it shuts off.

Comes with 2 red (660 nm) 3-watt LEDs, which are attached to a heat sink inside the cover. The LEDs will give the aquarium or sump a slight red color at night when the aquarium lights are off. You will need to get a timer so you can run the LEDs for up to 22 hours per day (not 24!). The LEDs never needs replacing.

The HOG1.3 growth surface will need to be cleaned every 7 to 21 days, by removing the inside cover, disconnecting the airline, and taking the inside cover to the sink so you can brush the algae off of the growth surface and the bubbler with a toothbrush. No hard scraping is needed; just brush it with a toothbrush. The Green-Grabber growth surface is permanently glued to the inside cover using epoxy, however a few of the Green-Grabber particles may dislodge during the first few cleanings, which is normal. Cleaning the growth surface, bubbler, and the inside cover takes about a minute with a toothbrush.

The HOG1.3 comes with a 6 month warranty: Warranty is for replacement or repair only; not a refund. Costs for shipping back to us are covered if you are in the U.S. Costs for shipping back to us are not covered if you are not in the U.S., however we will pay for shipping back to you. In either case, you will need to ship the entire unit back to us before we can ship a replacement. Warranty is limited to repair or replacement, and does not cover fish loss, personal injury, property loss, or direct, incidental or consequential damage arising from the use of it. The warranty and remedies set forth above are exclusive and in lieu of all others, whether oral or written, express or implied. We specifically disclaim any and all implied warranties, including but not limited to lost profits, downtime, goodwill, damage to or replacement of other equipment and property, and any costs of recovering animals, plants, tanks or other aquarium related items and/or equipment. We are not responsible for special, incidental, or consequential damages resulting from any breach of warranty, or replacement of equipment or property, or any costs of recovering or reproducing any equipment, animals or plants used or grown with this product.

Can be shipped to any country; you can find shipping costs by using the shopping cart; be sure to click "display rates". If you don't have a zip code, enter "zip code" instead. Note that shipping outside of the USA will probably require you to also pay an import charge when it arrives. We cannot mark it as "gift". The lowest cost overseas shipping is generally USPS First Class Mail International, although USPS Priority Mail International is recommended because it has insurance. The size of the shipping box is 10 x 7 x 5 inches (25 x 17.5 x 10 cm).

HOG1.3 size: Each cover is 6 5/8" wide x 8 3/4" high x 1 1/2" thick (16.6cm wide x 21.9cm high x 3.75cm thick). It requires at least 7" (17.5cm) of water to operate in.

Comments:

"Thank you! Working great! [HOG1.3]" -- Daniel Adelinis

HOG Instructions:
English (Word)
English (PDF)

Selection chart:
http://algaescrubber.net/WhichOne.jpg