+ Reply to Thread
Results 1 to 9 of 9

Thread: Flow Rate Dilemma

  1. #1

    Join Date
    Mar 2010
    Posts
    7

    Flow Rate Dilemma

    Let me preface this with an admission to being a newb. I'm an open minded newb, though, so I know that nothing I state is "fact," and I take criticism very well .

    I currently have a 20g freshwater tank. I'm planning to spend the next year learning as much as I can with the goal of moving to a reef tank in the neighborhood of 100g.

    The struggle I'm having at the moment is setting up a good flow rate for a scrubber in my current tank. The recommendations seem to be for shorter/wider screens and that's driving fairly high flow rates. My tank is populated by mostly very small fish, 1" length range. I don't know how they'll react to turning over the tank volume 8-12 times an hour. Can some of you more experienced folks chime in?

    Is it an option to run a lower flow rate to/from a sump and then run the higher rate within the sump circuit back through the scrubber? In other words, I could put 2 pumps in a sump. One supplies the overflow on my tank at a rate, say, of 80gph. The 2nd pump supplies the scrubber at 200-250gph and the scrubber drains back to the sump. I know that would get the flow rates where I want them, but would that provide adequate nutrition for the screen?

    Eric

  2. #2

    Join Date
    Jan 2010
    Location
    USA
    Posts
    163

    Re: Flow Rate Dilemma

    One time I thought I new everything then I woke up.

    Welcome to the forum.

    I believe that width to height ratio has more to do with optimizing your scrubber.

    Don't let that rule over other possibly more important considerations.

    If you want the correct flow along a long/short screen or a short/tall screen

    have a way to adjust the flow. Some of the people here use a ball valve to adjust flow.

    Hope this helps.

  3. #3
    Administrator
    Join Date
    Oct 2008
    Location
    Salt Lake City, Utah, USA
    Posts
    10,692

    Re: Flow Rate Dilemma

    Keep this one simple: Just use the overflow that you have now:

    Screen Width-----Gallons Per Hour (GPH)

    1" 35
    2" 70
    3" 105
    4" 140
    5" 175
    6" 210
    7" 245
    8" 280
    9" 315
    10" 350
    11" 385
    12" 420
    13" 455
    14" 490
    15" 525
    16" 560
    17" 595
    18" 630
    19" 665
    20" 700


    If you are doing an overflow feed, the overflow will determine how much flow you have to work with. You have to start from there, and size your screen accordingly. The maximum flow you'll get to the screen will be what's going through your overflow now. This is easy to figure out by counting how many seconds it takes your overflow to fill a one-gallon jug:

    60 seconds = 60 gph
    30 seconds = 120 gph
    15 seconds = 240 gph
    10 seconds = 360 gph
    8 seconds = 450 gph
    5 seconds = 720 gph


    Take this gph number that you end up with, and divide by 35, to get the number of inches wide the screen should be. For example, if your overflow was 240 gph, then divide this by 35 to get 6.8 (or just say 7) inches. So your screen should be 7 inches wide.

    How tall should the screen it be? That is determined by how much screen area you need, which is determined by how many gallons you have. Try to get one square inch of screen (lit both sides) for every gallon. If lit on only one side, double the screen area.

    When finished, this is how you want your flow to look:


  4. #4

    Join Date
    Mar 2010
    Posts
    7

    Re: Flow Rate Dilemma

    I see a lot of conflicting information on the net (no surprise) regarding what flow rate one should target, irrespective of filter type, in the tank. Most frequently, though, I'm seeing 4-6 times/hour recommended for FW tanks with small fish.

    If that's the case, I'm looking at flow rates in the 80-120gph range. At 35gph per 1" of screen, that puts me at 2 1/4" - 3 1/2" screen width and 7" - 10" of screen height. Since most of the scrubber designs I see highlighted here, certainly the Santa Monica designs, use L:W ratios directly opposite that, I "assumed" I wanted to head that direction, lol. Perhaps the problem was in my assumptions...

    Eric

  5. #5
    Administrator
    Join Date
    Oct 2008
    Location
    Salt Lake City, Utah, USA
    Posts
    10,692

    Re: Flow Rate Dilemma

    Wider is better for high performance, because it processes more water. But your goal here is just to get some scrubbing going, cheaply.

  6. #6

    Join Date
    Oct 2009
    Posts
    23

    Re: Flow Rate Dilemma

    I dont think flow rate for small tank has to be around 4-6 times/hr.
    I had gone as much as 20x/hr with small fishes like tetras,baby rainbows,loaches,small angels,catfishes etc
    And they wont mind the flow but its not like that flow was blowing them away,there were hindrance(rocks,driftwood,bog wood,plants etc).
    You just dont want a flow so strong that it blows your fish away.
    In planted FW tanks we usually go around atleast 17x/hr to avoid dead spots/algae in densely planted tanks.

  7. #7

    Join Date
    Apr 2009
    Location
    doncaster UK
    Posts
    212

    Re: Flow Rate Dilemma

    dont run the ats from the over flow its almost impossible to set up have the screen run off a pump and have the over flow run into the sump trust me i know ive spent ages trying to set mine up and to be honest pumping it is the way to go .

  8. #8

    Join Date
    Mar 2010
    Posts
    7

    Re: Flow Rate Dilemma

    The note on higher flow rates is encouraging. I guess I'll have to experiment a bit and figure out what my fish will tolerate. Perhaps I can set up a pump and run 10x or better for a bit and see how they respond.

    I'm a little disconcerted to hear about problems running the scrubber from the overflow, though. I don't really want to mount it above my tank. I'd like to put it below on a sump. I'll have to do some head scratching there.


    Eric

  9. #9
    Administrator
    Join Date
    Oct 2008
    Location
    Salt Lake City, Utah, USA
    Posts
    10,692

    Re: Flow Rate Dilemma

    Over flow is certainly harder than a pump, but a lot of folks are doing it (probably 25%).

+ Reply to Thread

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts